DSP control system is introduced for the hybrid linear step motor.
介绍一种混合式直线步进电机的DSP控制系统。
We designed and constructed the distributing step motor controlling system.
设计并构建了分布式步进电机控制系统。
It described the control circuits of single chip AT89C2051 used in step motor.
介绍了一种采用AT 89 C 2051单片机控制步进电机的实用电路。
Winding confirmations increase motor compatibility with most step motor drives.
缠绕大多数步进电机驱动器的确认增加电机的兼容性。
Among it, the choice and control of the hybrid step motor are introduced in details.
其中对步进电机的选用和控制进行了详细分析。
The design of step motor control card is based on DSP technique and PCI bus technique.
步进电机控制卡的设计采用了DSP技术和高速pci总线技术。
A type of software allotting pulses method for step motor has been presented in this paper.
介绍了一种步进电动机软件脉冲分配的方法。
In the automatic control, combination of the step motor with computer is more and more close.
自动控制中，步进电动机与电子计算机的结合越来越紧密。
This type of rotor position sensor lays a foundation for the closed-loop control of step motor.
这种新型位置传感器为进一步实现步进电动机闭环控制奠定了基础。
Through controlling the step motor moving, the accurate control of the piston pump is obtained.
通过控制步进电机的运动，来实现对柱塞泵流量的精确控制。
This article presents a new type of ring - distributor for microstepping drive of power step motor.
本文介绍了一种适合于功率步进电机细分控制的环形分配器。
The starlike torque graph is an effective method in analyzing the step running of rotatable step motor.
在旋转步进电动机的步进运动分析中，转矩星形图是一种比较有效的工具。
Because of the many merits of the step motor, the step motor is selected to drive the machine Settings.
由于步进电动机的一些特殊优点，论文采用步进电动机来驱动机械机构。
This design is the main engine will take the step motor actuators provide an idle by-pass inlet channel.
本设计主要是将汽油机的带步进电机的怠速执行器提供一个旁通的进气通道。
The design method and driving circuit for microstepping control of step motor are described in the paper.
本文描述步进电机微步控制的设计方法及驱动电路。
In this paper, the closed-loop control method of hybrid step motor using the harmonic back EMF is investigated.
研究了利用谐波反电势信号实现混合式步进电动机闭环控制的方法。
In the past for a long time, step motor to take up a large market, but China is gradually replaced for servo motor.
在过去很长一段时间里，步进电机占很大的市场，但目前正逐步为伺服电机所取代。
The paper introduced the basic characteristic, parameter and application of high resolution five-phase hybrid step motor.
介绍高分辨率五相混合式步进电动机的基本特点、参数及应用。
A design is described in the paper that step motor motion controller is a down location control unit based on DSP kernel.
本文提出了一套基于DSP内核的运动控制器的设计方案。
This system uses a high-low supply voltage and a series resistance for increasing the working frequency of the step motor.
本系统采用了高低压驱动电源和串联电阻法，以提高步进电机的工作频率。
A motion controller interchangeable for servo motor and step motor constructed by motion control chip PCL240AS is introduced.
提出一种用运动控制芯片PCL240AS构造的伺服电动机和步进电动机通用的运动控制器。
On the basis of the principle of step motor, this paper introduces the connection between step motor and single chip processor.
本文简单的介绍步进电机实理，在这基础上，阐明步进电机与单片机结口方法。
But the step motor efficiency is low, the ability is not big, load drag pulse equivalent cannot too big, speed range is not big.
但步进电机的效率低，拖动负载的能力不大，脉冲当量不能太大，调速范围不大。
The article discusses the design aim and principle of an intelligent cycle pulse distributor used for power supply for step motor driving.
讨论了一种用于步进电机驱动电源的智能型脉冲分配器的设计目的和设计原理。
This paper gives the design of a new type, high torque VR step motor-dual stator VR step motor which can be used to drive robots directly.
本文给出一种新型，高转矩VR步进电动机——双定子VR步进电动机的设计。该电机可用于机器人的直接驱动。
The design of the single chip system, sample box thermostat circuit, sample position detecting circuit and step motor control circuit are discussed.
着重讨论了单片机系统、样品箱恒温电路、样品位置检测电路和步进电机控制电路的设计。
This article introduced the matching selection of step motor for wire-cut electric discharge machine by analyzing the special stress of the machine.
通过对电火花线切割机床在加工过程中的特殊受力分析，给出步进电机的匹配选择方法。
The software connection problem between the output of non-model controller and step motor, is discussed using step motor as the actuator of control system.
以步进电机作为控制系统的执行机构，讨论了无模型控制器的输出与步进电机之间的软件连接问题。
Introduce the drive control of step motor and the PWM principle of DSP, a detailed discuss on accelerate and decelerate control of step motor also include.
介绍步进电机的驱动控制和DSP的PW M脉宽调制原理，详细阐述了DSP实现步进电机的加减速控制问题。
During the protess of elecrospark wireelectrode cutting, step motor makes mistakes because of outof synchronism, which will affect accuracy of process directly.
电火花切割加工中，步进电动机失步产生误差，直接影响加工精度。
应用推荐