In the operation of jigging machine, we should timely adjust blowing rate, water quantity, feeding and layout.
在跳汰机的作业的操作中，要适时调节风量、水量、给料和排料。
The influence of contents of blowing agent AK on the curing rate, blowing rate of silicone rubber were discussed.
研究了发泡剂AK用量对硅橡胶硫化速率和发泡速率的影响。
The reasonableness and practicability of way direct to monitor the blowing rate of axial fan have been verified in the article.
对电厂动调轴流式风机，用运行风量直接监测方法的合理性与可行性进行了论证。
This article focuses on technical issues such as feeding, blowing rate, water quantity, feeler lever and layout quantity of jigging machine.
本文主要阐述了跳汰机的给料、风量和水量、探杆、排料量等技术问题。
Experiment results show that gas phase made silicon dioxide performs an important function in increasing the blowing rate of PVC paste resin.
实验表明，气相法二氧化硅对提高聚氯乙烯糊树脂的发泡倍率起着重要作用。
There were optimum matching of top blowing rate and bottom blowing rate and corresponding location during top-bottom blowing to get better effect.
顶底复吹时，为取得较好的效果，亦存在顶吹-底吹气量的最佳配合及相应的有利位置。
The smelting process was strengthened by using high top pressure, high pressure drop, large blowing rate, reduced tuyere section and enhanced blasting velocity.
采取高顶压、高压差、大风量、缩小风口直径、提高风速和鼓风动能等措施进一步强化冶炼；
Discussion focus on the influences of technological parameters like spinning temperature, spinning speed, blowing rate, oil finishing as, well as texturing on the products quality.
重点讨论了纺丝温度、纺丝速度、侧吹风风速、上油、拉伸变形等工艺参数对产品质量的影响。
The experiment result of the sintered metal tube shows that the uneven rate of axial blowing is lower than 10%, and the flow is steady.
烧结金属筒实测结果显示，吹风径向不匀率小于10%，且气流稳定。
It is found that slags decrease the rate of vacuum denitrogenation and vacuum argon blowing decreases the denitrogenation resistance of slags.
结果表明，熔渣降低真空脱氮速率，底吹氩能减少熔渣对真空脱氮的阻力。
At the final blowing stage, the relation between carbon content and decarbonization rate can be described by cubic function;
吹炼末期，碳含量和脱碳速率的关系可用三次方函数描述；
The effects of bottom blowing flow rate, top blowing flow rate and top lance level on mixed time in iron bath of smelting reduction furnace were studied with water modeling.
通过铁浴式熔融还原炉的水力学模型，实验研究了底吹流量、顶枪流量和顶枪枪位对熔融还原炉内混匀时间的影响。
The results show that the entrainment of slag in tundish with gas curtain was mainly affected by gas flow rate and the position of gas blowing.
结果表明，气幕挡墙的位置和吹气量是影响中间包卷渣的主要因素。
The result shows that the effect of top blowing oxygen jet on the mixing time and circulation flow rate can be disregarded.
结果表明，顶吹氧射流对钢包混匀时间和循环流量的作用可以忽略。
It showed that the heating and cooling temperature and rate was the factor effecting the process except for the blowing agent variety and the loading weigh.
实验研究显示，影响滚塑发泡工艺的因素除了发泡剂种类以及加入量，还有加热冷却温度、速度等等。
It was found that gas blowing at the bottom effectively eliminated the short flow, strengthened the mixed flow of gas curtain regions and increased the total inclusion removal rate.
研究表明，中间包底部吹气过程可以有效改善钢液的流动状态，消除短路流，增强“气幕墙”区域钢液的混合，并有效促进了夹杂物在中间包内上浮去除。
The effect of gas bubble size, injection rate and blowing time on removal of hydrogen and inclusion in liquid steel during refining has been studied and analyzed by theory calculation.
通过理论计算研究和分析了钢液气泡直径、吹气量和吹气时间对精炼时去氢和夹杂的影响。
It is right. After the floor is paved, the rate of air leakage is no more than 2%. It is mainly used in underground blowing-in fo air conditioner for 5a class office building.
密封性能好，地板安装好以后漏风率不大于2%，主要用于5a级写字楼空调地下送风办公室。
It is right. After the floor is paved, the rate of air leakage is no more than 2%. It is mainly used in underground blowing-in fo air conditioner for 5a class office building.
密封性能好，地板安装好以后漏风率不大于2%，主要用于5a级写字楼空调地下送风办公室。
应用推荐