Click OK and close the Command window.
点按“确定”，并关闭命令窗口。
Click Open in the command window to launch it.
在命令窗口中单击open以启动它。
You will see the output similar to the following in the command window
您将在命令窗口中看到与以下类似的输出
When the command window appears, enter the following at the command prompt.
当命令窗口中，输入在命令提示符下。
Verify that the command has been accepted by typing "db2set" in the command window.
在命令窗口中键入“db2set”来验证命令是否已被接受。
After you run this command, a window displays showing the boot process.
运行此命令后会出现一个显示引导进程的窗口。
If you set the class path temporarily, each time you open a new command window you need to set it again.
如果是临时设置类路径，那么每次打开新的命令窗口时，都需要再次设置它。
To verify the installation, open a command window and issue the commands shown below.
为了验证安装是否成功，需要打开一个命令窗口并发出如下命令。
You should also be familiar with the DB2 command window and running DB2 scripts.
您还应该熟悉DB 2命令窗口和运行DB 2脚本。
Open a db2 command window on the system where the application server is installed.
在安装应用服务器的系统上，打开一个db 2命令窗口。
Open your Command Prompt window and navigate to the project folder as you did previously.
打开CommandPrompt窗口并导航到项目文件夹，就像之前所做的一样。
From the command prompt window, type dbaccess.
在命令提示窗口中，输入dbaccess。
From the db2 command window issue: db2 list applications.
在db 2命令窗口中，发出：db 2listapplications。
You can watch for it in the connectors command window.
您可以在连接器命令窗口中进行查看。
Close the command prompt window.
关闭命令提示窗口。
Open the command line processor window and start DB2.
打开命令行处理程序窗口并启动DB2。
A system command window is displayed to show the progress.
将显示一个系统命令窗口，其中将展示进度。
Open a DB2 command window and establish the database connection.
打开DB 2命令窗口并建立数据库连接。
打开DB 2命令窗口。
To start the apply process, go to a command window in Windows and issue
要启动应用过程，在Windows 中定位到一个命令窗口，并发出
From a command window or shell, run the amqsput utility, as follows.
从命令窗口或外壳程序中运行amqsput实用程序，如下所示。
From a command window or shell, execute the runmqsc command, as follows.
从命令窗口或外壳程序中执行runmqsc命令，如下所示。
When you run the make xconfig command, a window will appear similar to Figure 4.
当您运行make xconfig命令时，将显示出一个类似于图4的窗口。
Temporarily by setting the CLASSPATH environment variable in a command window or shell.
临时地，通过在命令窗口或 shell中设置 CLASSPATH环境变量来实现。
Open a command window and change to the tcpmon directory.
打开一个命令窗口，并转到tcpmon目录。
In a command prompt window, type the following command: db2cmd.
在一个命令提示窗口中，键入以下命令：db2cmd。
On the mpstat command window, you can observe the following.
在mpstat命令窗口中，可以看到以下输出。
In the mpstat command window, you can observe the following.
在mpstat命令窗口中，可以看到以下输出。
In the command prompt window, type the following command, and then press enter.
在命令提示窗口中，键入以下命令，然后按enter键。
And on the mpstat command window, you can observe the following.
在mpstat命令窗口中，可以看到以下输出。
应用推荐