The relation of thermal and temperature of material is studied through thermal loading.
对热载荷加载研究了材料的应力与温度之间的关系。
Piston needs to be cooled efficiently with increase of thermal loading of diesel engines.
由于柴油机热负荷不断提高，必须要对活塞进行有效冷却。
The factors influencing the safety of the structure were summarized, and thermal loading was the most damaging.
分析总结了夹套结构安全的影响因素，指出温度载荷可影响设备的正常运行。
The research method and the results described in this paper will pro-vide a basis for thermal loading prediction of air-cooled diesel engines.
文中所论及的研究方法和初步结果可为风冷柴油机热负荷预测提供依据。
Thermal loading concentrated on the outer circumference of the discs during the engagement time may result in a form of conical deformation. Disc waviness may ar…
在离合器外齿片片内缘加载，接合时热负荷集中于片内半径区域，易引起离合器片的波浪形翘曲。
This thesis is on the basis of the research of diesel engine type 4135 etc, and the complete and systematic numerical modeling and malfunction simulation for thermal loading.
本文以4135柴油机等机型作为研究对象，对其热负荷进行了全面系统的数值模拟和故障仿真。
Using the solutions, the evolution processes of thermal consolidation for a cylinder under axisymmetric conditions are studied for both constant and variable thermal loading conditions.
利用这一解答，分析了常温度荷载和变温度荷载两种情况下圆柱热固结的演化过程。
Cause analysis of the water cooled wall tube burst focused on irrational points of design, excessive thermal loading, changes of coal category, burner defects and deposits in throttle valves.
着重从锅炉设计不合理、热负荷过高、煤种变化、燃烧器的缺陷及节流阀结垢等方面分析了水冷壁爆管的原因，指出必须进行锅炉改造。
A quantitative relationship between dynamic fracture toughness and temperature and loading rate has been obtained through thermal activation analysis.
通过热激活分析，可以获得定量描述动态断裂韧性、温度及加载速率之间的关系。
There is a fracture transition caused by loading rate. Through thermal activation analysis, a quantitative relationship was found.
通过热激活分析，获得了断裂激活能以及与温度和加载速率相关的定量化关系。
The results indicated, when compared to the pure epoxy resin, that the mechanical and thermal properties of the nanocomposite could be greatly improved by addition of low clay loading.
结果表明，少量蒙脱土的加入可以较大地提高材料的力学性能和耐热性能，对环氧树脂同时起到了增韧增强的作用。
The material stress in rolling contact results from the external loading of a bearing under contact pressure as well as from additional stresses of a mechanical, chemical or thermal nature.
材料的应力在滚动结果从外在负载下的轴承接触压力以及从附加应力的机械、化工或热性质。
The result of transient state analysis indicated the thermal-mechanical effect on seal face during loading, the seal surface parameter dropped steadily during unloading.
理想瞬态分析实例表明，加载过程中密封端面产生热机效应，稳定减载过程中端面参数平稳下降。
It expounds that the key of solving thermal transient sealing problem is to obtain the thermal increment of stud-bolt loading.
阐明了热瞬态密封问题求解的关键是给出螺栓载荷的热态增量；
If the constrained thermal cycle stopped upon cooling while the forward martensitic transformation was in progress, the loading stress strain curves exhibited the stress plateau immediately.
如果在冷却过程中发生正相变的时候停止冷却并加载，则加载应力-应变曲线只出现应力平台。
The present electrode had the characters of low platinum loading and high catalytic performance which was higher than counter electrodes prepared by thermal decomposition and platinum foil.
所制备的电极具有载铂量低、催化活性高的特性，比纯铂片对电极以及热解法制备的载铂对电极具有更高的活性。
The simplified elastic-plastic analysis was used for the thermal expansion loading.
事故工况下温度载荷对设备的影响采用了简化弹塑性分析的方法。
Dynamical cavitation in a spheroid composed of two incompressible thermal-hyperelastic Gent-Thomas materials under boundary dead-loading is examined.
该文研究了由两个不可压热超弹性球体组合而成的物体在突加表面均布拉伸载荷作用下空穴的动态生成问题。
It is found that the loading capability and pith Angle increase significantly under influence of thermal effect, and roll Angle changes little.
热效应使气体黏度和承载能力增加，从而使磁头飞行高度和俯仰角增大，但对侧翻角没有明显影响。
The work volume for coal loading, unloading and distribution in coal yard of thermal power plants is very great, which needs to increase the automation degree.
火电厂煤场装车、卸车、配煤的工作量很大，迫切需要提高其自动化程度。
Cast steel cooling stave has favorable impact toughness and cyclic-temperature loading fatigue, and it has no thermal resistance of coat and gas gap witch exist in ductile iron cooling stave.
铸钢作为冷却壁的材料具有良好的冲击韧度和耐热疲劳性能，并且结构上完全去除了球墨铸铁冷却壁的防渗碳涂层和冷却水管与本体之间的间隙热阻。
Cast steel cooling stave has favorable impact toughness and cyclic-temperature loading fatigue, and it has no thermal resistance of coat and gas gap witch exist in ductile iron cooling stave.
铸钢作为冷却壁的材料具有良好的冲击韧度和耐热疲劳性能，并且结构上完全去除了球墨铸铁冷却壁的防渗碳涂层和冷却水管与本体之间的间隙热阻。
应用推荐