A simplified calculation model of magnetic field from substation busbars is established.
构建了配电房母线磁场分布计算的简化模型。
A new simplified calculation model was proposed for evaluating the isolation effect of open trenches.
提出了影响因子的概念，建立了空沟隔振效果的简化计算模型。
In this paper, a simplified calculation model has been proposed for analyzing the dynamic characteristics of tube in tube structure.
本文为高层建筑筒体结构动力特性分析提供了一个简化计算模型。
In this paper, a simplified calculation model has been proposed for analyzing the effecting of bending deformation of jet attachment in parallel flows.
本文提出平行气流中附壁射流弯曲变形的简化计算模型。
Taking the hybrid ground source heat pump with cooling tower as research object, a simplified calculation model of buried tube heat exchanger is established.
以配置冷却塔的复合式土壤源热泵为研究对象，建立了地埋管换热器简化计算模型。
Based on the settlement calculation method of composite pile foundation, calculation model in compressive area method of reliability is established, and simplified calculation model is presented.
从复合桩基的沉降计算方法出发，建立了沉降可靠度分析模型，通过对各种计算模型的分析比较，提出了沉降可靠度的推荐计算方法。
As there is only one parameter used in the model, so the simulation calculation of motor vehicle performance is greatly simplified.
由于该模型只用一个参数来描述，所以极大地简化了整车性能的模拟计算。
Based on the softened truss model for reinforced concrete, a simplified calculation method is proposed to simulate the whole loading process of high strength reinforced concrete panels in this paper.
在钢筋混凝土转动角软化桁架模型的基础上，推导出从应力到应变的简化计算方法来模拟高强钢筋混凝土墙板受力全过程。
Using the results from finite element analysis of turbine rotor suppressed in heat stress, and simplified theoretical calculation equations, a mathematical model is established.
采用汽轮机转子热应力的有限元分析结果和简化的理论计算公式，建立汽轮机转子热应力的数学分析模型。
According to force analyzing of missile, the complicated force calculation has been replaced by the fitting formula, and a simplified trajectory model has been developed.
根据导弹受力特性分析，用拟合公式替代了复杂的外力计算，并建立了简化的外弹道模型。
Based on the model of simplified road, the effects of different double-wheels sizes of lorry on the bottom strain of asphalt layer were analyzed by the method of numerical calculation.
以简化道路模型为对象，以数值计算方法为手段，研究了载重货车不同单边双轮轮距对沥青面层层底应变的影响。
Upon the analysis to the behavior of the deflector under the instantaneous shock type external loading, the paper simplified the structure calculation model.
在分析了导流器承受瞬间冲击型外负荷的作用特性后，对结构计算模型进行了简化；
In this paper the companion model of passive filters is established, thus, the calculation is greatly simplified.
文中还建立了无源滤波器的综合友模型，从而大大简化了计算。
Then the model was simplified considering its characteristics, and a modified error correction model was obtained which was less complex in calculation.
并根据偏心误差模型的特点，对其进行简化，得到易于数学计算的偏心误差修正模型。
With the simplified network model, the fault can be flexibly and efficiently searched by minimal cutset method, and the network reconstruction of and power flow calculation can be conducted.
在简化网络模型基础上可灵活、高效地用最小割集法搜索故障、进行网络重构和潮流计算。
A simplified model for directional collapse of a construction is presented and a calculation formula on the minimum height of blasting cut is developed.
对建筑物的定向倾倒提出了简化模型，推导了最小炸高的计算公式。
P- restoring force model, simplified calculation methods of ductility coefficient and energy dissipation are given on the basis of integral calculation and parameter analyze for CFRST.
在数值计算和参数分析的基础上，提出矩形钢管混凝土压弯构件荷载—位移恢复力模型，延性系数和耗能比的简化计算方法及相关计算公式。
The equivalent circuit for model parameter calculation is also given, so a calculation for complicated mechanism could be simplified to a electrical circuit calculation.
同时作出了模型参数计算的等效回路图，将复杂机械机构计算简化为电回路计算。
Furthermore, as for the fork blade roots, a simplified contact model is put forward and according to the calculation results, a more reasonable pin-hole load distribution model is given in this paper.
另外，对叉型叶根，文中提出了一种简化的接触模型，并根据计算结果给出更合理的销钉孔载荷分布拟合公式。
Via the construction of geometric model, calculation formula for the head of worm lathe tool has been deduced, which has simplified calculation program.
通过构建几何模型，推导出蜗杆车刀头部的计算公式，简化了计算程序。
The suitable simplified calculation formula for calculation at working site is presented on the basis of making mathematical transformation and analysis to the mathematics model.
在对数学模型进行数学变换和数学分析的基础上，得出了适用于作业现场计算的简化算式。
Then, the complex integral calculation problem in the reliability model of stress and strength interference was simplified by using the Monte Carlo Simulation Method.
其次，采用应力与强度干涉模型和蒙特卡罗模拟法，解决了可靠度计算公式中复杂积分的计算问题。
Based on the test and analysis a simplified formula for the joints' aseismic calculation was developed. The calculated results are in good agreement to those of the model test.
在试验的基础上给出了接头极限承载力的简化计算公式，计算结果与模型试验结果吻合较好。
The simplified aseismic calculation model for transmission tower-line system considering pile-soil dynamic interaction is given.
提出了考虑桩–土–结构动力相互作用的输电塔线体系简化抗震计算模型。
The simulation of mixed growth algorithm show: model is simplified and speed of the calculation is accelerated.
混合生长算法的提出简化了模型，加快了计算的速度；
This paper presents a theoretical model for realistic annular pressure loss calculation in which the eccentricity is a function of the well depth and a simplified method for field calculations.
本文介绍偏心度为井深函数的实际环空中压降计算的理论模型和便于现场使用的简化计算方法。
The calculation of simplified model is also compared with that of real model.
比较了酞菁简化模型与真实模型计算结果的差异。
A two-direction shear deformation finite element model is presented in which a three-dimensional problem is reduced to a two-dimensional one and thus the calculation is much simplified.
文中提出了“双向剪切变形”有限元模型，使三维问题简化为二维问题，计算工作量大为减少。
Under the condition that the precision is assured, the calculation has been simplified (compared with three dimensional model).
在保证精度的条件下简化了计算(相对于三维)。
The calculation of simplified model is also compared with that of real model. Calculation results agree well with the conductivity of PHTH...
比较了酞菁简化模型与真实模型计算结果的差异。
应用推荐