A new technology of laser surface micro-molding is introduced, and the mechanical face seal ring cross-scale processing of the geometric shape is researched.
介绍了激光表面微造型新工艺新方法，对机械密封环端面进行跨尺度的几何形貌加工工艺研究。
Great attention paid for designing and applying seal Chambers for mechanical face seals will improve seal performance, prolong their life and increase the machine reliability.
重视设计和使用机械密封的密封箱可以改善机械密封性能、延长密封寿命、提高设备及机泵的工作可靠性。
For motor frame size 180 and above, the inner mechanical seal shall be constructed with a solid block carbon rotating seal face and a solid block silicon carbide stationary seal face.
用于尺寸180以上的电机机架，内置的机械密封结构应该采用一块整体结晶碳旋转密封面和一块整体结晶碳化硅固定密封面。
Mechanical seal: seal face, gasket and shaft seal, etc parts must be undamaged, otherwise will result in over leakage, sure to change parts with wear and tear or damage.
机械密封：密封面、密封垫及轴封等元件必须完好，否则将导致过度泄漏，对有磨损或损伤的元件必须更换。
Changes in the spring performance will directly affect the mechanical seal face pressure.
弹簧性能的发生变化将会直接影响机械密封端面比压。
The inner mechanical seal shall be constructed with a solid block carbon rotating seal face and a solid block silicon carbide stationary seal face.
内置的机械密封结构应该采用一块整体结晶碳旋转密封面和一块整体结晶碳化硅固定密封面。
The outer mechanical seal shall be constructed with a solid block silicon carbide rotating seal face and a solid block silicon carbide stationary seal face.
内置的机械密封结构应该采用一块整体结晶碳旋转密封面和一块整体结晶碳化硅固定密封面。
Mechanical seal: use of WB2 and st non-water-cooled adjustable end face sealing technology, composed of silicon carbide, high purity alumina ceramic, packing PTFE and graphite etc.
机械密封：采用WB2型、ST型不用冷却水可调式端面密封技术，由碳化硅，高纯度氧化铝陶瓷、填充四氟，石墨等材料制成。
This paper describes and analyses the reasons of the failure of dual-encl-face mechanical seal for hydrocarbon pump and proposes a reformation and design method.
本文阐述并分析了轻烃泵用双端面机械密封的特点，提出了改进方法和设计依据。
This paper introduces some results on the project "study on face deformation of mechanical seal."
本文介绍了“机械密封环端面变形研究”课题的初步研究结果。
The result of transient state analysis indicated the thermal-mechanical effect on seal face during loading, the seal surface parameter dropped steadily during unloading.
理想瞬态分析实例表明，加载过程中密封端面产生热机效应，稳定减载过程中端面参数平稳下降。
The dynamic performance of mechanical seal has significant influence on sealing system stability, small vibration can cause sealing leakage increasing and end face excessive wear.
机械密封动力学性能对密封系统稳定性有很大的影响，微小的振动会导致密封泄漏量增加和端面磨损加剧。
The wear rate of the end face of soft ring of B104a -70 mechanical seal was calculated and analyzed.
对B104 a - 70型机械密封软质环端面的磨损率进行了计算和分析。
The reason of the seal's failure was analyzed. A new mechanical seal was developed which has an edge-seal end face, and the rubber lip seal was replaced by the mechanical seal.
设计一种刃口型密封端面的机械密封，代替原泵轴封采用的橡胶油封。
Mechanical seal type XM31A has a single seal face and multi-spring unbalanced structure, and is driven by screw transmission.
XM31A型机械密封为单端面、多弹簧非平衡型结构。采用传动螺钉传动。
The main contents and achievements are summarized as follow:1. A theoretical model has been developed to investigate hydrodynamic effect of mechanical seals with a laser-textured pores seal face.
主要研究内容和结论如下：1。建立了激光加工多孔端面机械密封的流体动力学分析模型，根据假设，一个孔栏上的液膜压力分布可表征整个密封面上的液膜压力。
Impeller with against pine device, Mechanical seal face material USES silicon carbide - silicon carbide, durable, safe and reliable.
叶轮具有防松装置，机械密封端面材质采用碳化硅-碳化硅，经久耐用、安全可靠。
Impeller with against pine device, Mechanical seal face material USES silicon carbide - silicon carbide, durable, safe and reliable.
叶轮具有防松装置，机械密封端面材质采用碳化硅-碳化硅，经久耐用、安全可靠。
应用推荐