The floor was sometimes caulked and filled with water to a depth of about a meter for mock sea battles.
地板有时灌满了深度约一米的水，以模拟海战。
From the upper edge of the existing structure, with a depth of 25meters, the new apartments of 8 meter modules stack continuously upwards.
现有结构高25米，再向上便是每8米一单元堆叠起来的新公寓。
The measuring principle, hardware circuit principle and software design of WGL-1 intelligent mining borehole depth and dip meter are introduced.
介绍了智能WGL-1型采矿中深孔深度倾角测量仪的测量原理，硬件电路原理及软件设计。
The deepest place is two meters but you can swim in the shallow area, which is only l. 4 meter in depth.
最深的地方有两米，但是您可以在浅水区游泳，那里只有1.4米深。
A mathematic model for the relationship between the rate of heat transfer per meter borehole and the depth of borehole as well as the flow rate was built.
建立了钻井单位井深换热量与钻井深度、流量变化关系的计算模型。
No swimming, tree climbing or rock climbing is allowed. Never go into an area where water depth exceeds half meter.
不准游泳、爬树或攀石，也不应进入水深超过半米的地区。
Scientists from 10 nations have now almost completely drilled through a 3,000-meter depth of ice high in the Antarctic mainland.
来自10个国家的科学家们如今几乎已经钻穿了南极大陆3000米深的冰原。
The key indicators for evaluating the benefit of explorational activity should include 2-D seismic cost per kilometer, 3-D seismic cost per square kilometer, and drilling cost per meter in depth.
每公里二维地震成本、每平方公里三维地震成本和每米进尺钻井成本是评价勘探作业效率的关键指标。
"If we were to take all the water that is locked up inside the moon, and put it in a homogenous layer on the lunar surface, it would cover the moon to about a meter depth," he explained.
“如果我们把蕴藏在月球内的水份全部取出，并将其覆盖在月球表面的话，该含水层的深度将达1米。”他解释道。
In the middle of the Atlantic ocean, with a salinity of 3.2 %, a VLF signal will penetrate down to a depth of 10-20 meter, barely periscope-depth for a modern large scale submarine.
在大西洋中部，海水的盐度为3.2%，甚低频无线电信号可以穿透到海面下10 ~20米的深度，几乎就是现代大型潜艇的潜望镜深度。
This paper presents the information of the effect, measured with a tele-strain-meter, of work material, feed, cutting speed, depth of cut, number of teeth and helix Angle etc.
本文在高速滚齿机上，利用遥测应变仪，测定了工件材料，进给量，切削深度，切削速度，齿轮齿数及螺旋角等对力矩的影响，并得出径节为8时的力矩公式。
This paper presents the information of the effect, measured with a tele-strain-meter, of work material, feed, cutting speed, depth of cut, number of teeth and helix Angle etc.
本文在高速滚齿机上，利用遥测应变仪，测定了工件材料，进给量，切削深度，切削速度，齿轮齿数及螺旋角等对力矩的影响，并得出径节为8时的力矩公式。
应用推荐