The Problem of bars subjected to axial tension and bending is also described here.
对于拉弯构件问题，本文也作了论述。
When flange is withstanding axial tension or crook moment, its purpose should be considered otherwise.
当法兰承受轴向拉力或弯矩时，应另行考虑其作用。
The authors introduce a sensor based on magneto-elastic effect to measure the axial tension of steel cable.
本文介绍了一种建立在磁弹效应原理基础上的可用来测量钢索轴向拉力的传感器。
The cables will be slack when the cables are not subject to axial tension due to the excessive motions of platform.
在不承受轴向张力时，纤维系缆将处于松弛状态，因此在深海平台大幅、往复运动下，系缆将可能出现绷紧和松弛两种状态。
The fatigue behavior of concrete under axial tension with constant and variable amplitude cyclic loading is investigated.
基于室内试验，研究了混凝土在等幅和变幅重复荷载作用下的轴拉疲劳性能。
By using molecular dynamics(MD) method, the axial tension and compression of the (10,10) carbon, BN nanotubes and nanopeapods were simulated.
采用分子动力学方法，模拟了（10，10）碳、氮化硼纳米管及纳米豆荚的轴向拉伸与压缩。
The lower chord of a vierendeel truss, when loaded, is subjected to the combined action of prestressed compression, large axial tension, moment and shear.
空腹屋架下弦处于预压力、强大的轴拉力、弯矩和剪力共同作用下工作。
The practice proves that it needs to be further discussed that the flexible suspenders of a large-span half through bridge are designed as axial tension members.
实践证明，大跨中承式拱桥柔性吊杆按照轴心受拉杆件进行设计的方法有待商榷。
Complete stress-deformation curves for concrete in tension were obtained from axial tension tests in which some of the specimens were tested under cyclic loading.
本文通过试件的中心受拉试验，测定了砼的受拉应力-变形全曲线。部分试件还进行了反复荷载试验。
The calculating method, optimum strengthening design and application of axial tension and compression members strengthened by prestressing is analyzed and discussed.
分析和研究了预应力加固轴心受拉和轴心受压构件的计算方法、优化加固设计及其应用。
Fiber tension can be reflected indirectly by measuring axial tension. Therefore the acquisition and processing of axial tension is the core part of fiber tension test.
光纤拉力可以通过测量轴向拉力来反映，因此轴向拉力数据的采集和处理是光纤拉力测试的核心部分。
Through a lot of experiments and analysis, it was pointed out that the twist number of steel wire in torsion test decreased gradually with increasing axial tension load.
本文通过大量的试验和分析，得出钢丝扭转试验时，随着轴向拉力负荷的增加，其扭转次数趋于递减的变化过程。
And use the fourth strength theory, the axial tension in the coiled tubing under the influence of internal and external pressure from a comprehensive stress of checking.
并利用第四强度理论，对连续油管在轴向拉力与内外压力的作用下的综合应力进行了校核。
It is difficult to pull out the bolt with ordinary socket wrench that can not provide axial tension because of the bolt drilling hole deformation and the collapse of holes.
煤矿井下可回收锚杆一般用于煤层巷道，由于锚杆钻孔的变形和塌孔等原因，用普通套筒扳手拆卸锚杆时，因不能给锚杆提供轴向拉力，很难将锚杆拆卸拔出。
It shows the axial tension initial cracking strength of concrete increases with the increasing of steel fiber volume ratio and enhancing of concrete strength grade separately.
结果表明：混凝土轴拉初裂强度分别随钢纤维体积率的增大和混凝土强度等级的提高而增大。
A photoelastic study for the viscoelastic stress-concentration factors in bars with a round hole under axial tension load, using self-made viscoelastic materials is presented in this paper.
本文利用自制的光粘弹性材料，用光弹性法研究了在轴向拉伸荷载作用下带有圆孔的杆件中的粘弹性应力集中系数。
According to the geologic characteristics and development status of the Yushulin Oil Field, the mechanism of casing damage is studied and the effect of axial tension on casing intensity is discussed.
根据榆树林油田地质特征和开发现状，研究了套管损坏机理，讨论了轴向拉应力对套管强度的影响。
At least one blade Angle bearing of a pair of such bearings permits an axial movement of the respective tension or carrier bar, whereby the latter is able to take up bending loads.
至少有一个叶片角度轴承的一对，如轴承许可证的轴向运动各自的紧张或承运人的酒吧，而后者则是能够采取行动的弯曲载荷。
Experimental and theoretical researches were undertaken on the elastic modulus in tension and bending of 3d braided composites containing axial yarns.
对包含有轴纱的三维编织复合材料的拉伸弹性模量和弯曲弹性模量进行了试验研究和理论分析。
The sensor (11) is preferably under axial pre-tension in the installed state.
所述传感器（11）在安装状态下优选处于轴向预紧之下。
It is shown that the interval tension fracture would occur repeatedly under large axial compression stress, which forms the layered failure.
研究结果表明，在很大的轴向水平压力作用下，介质会产生间隔的拉伸裂缝，形成分层断裂现象。
It is shown that the interval tension fracture would occur repeatedly under large axial compression stress, which forms the layered failure.
研究结果表明，在很大的轴向水平压力作用下，介质会产生间隔的拉伸裂缝，形成分层断裂现象。
应用推荐