• Rotational molding process provides the product extra strength and sturdy feature.

    塑工艺成型,产品结构坚固。

    youdao

  • And the development of different kinds of plastics for rotational molding especially PE were discussed.

    探讨了可用于回转成型各类塑料尤其是聚乙烯的研究开发情况。

    youdao

  • The development of the plastics for rotational molding rotational molding machines and technics was reviewed.

    综述回转成型塑料设备工艺研究进展。

    youdao

  • It introduced the processing technology of the product from composite materials by means of rotational molding method.

    介绍利用旋转模塑方法成型复合材料制品工艺

    youdao

  • The article deals with the situation and development tendency of rotational molding of plastics both at home and abroad.

    本文简要介绍了目前国内外滚塑工业现状发展趋势

    youdao

  • The defects of stamping and plastic-absorbing technology were analyzed, and the principles and merits of rotational molding were introduced.

    分析了冲压技术技术缺陷介绍了滚塑成型原理优点

    youdao

  • Rotational molding is good to deal with large and complex tanks. And rotationally molded tanks can be very strong by increasing its wall thickness.

    塑工艺适合大型复杂水箱油箱并且塑的水箱或油箱可以通过调整来增加强度。

    youdao

  • The method and application of rotational molding were introduced. The intention and signification of solving defects of rotational molding products were presented.

    简要介绍了旋转成型方法用途,指出了研究并解决滚塑制品缺陷目的意义

    youdao

  • It was suggested that in the rotational molding, the initial viscosity controlled the wall thickness of the product and the gel rate controlled the uniformity of the wall thickness.

    试验表明,树脂体系初始黏度制品最终影响较大,体系凝胶速率对制品壁厚均匀性影响较大。

    youdao

  • Steel, net, plastic 3-1 - will be welded to the steel wire mesh surface to polyethylene as raw material, the use of rotational molding technology, an overall shape in the steel surface.

    3合1——钢网焊接于钢体表面聚乙烯原料采用技术一次整体成型于钢体表面。

    youdao

  • The heating times during the rotational molding of the hollow plastic products were studied according to the theory of heat transfer and interfacial movement, and an algorithm was proposed.

    为了解决成型工艺加热时间难以确定问题,依据传热学界面运动理论进行了滚成型加热时间的研究,提出了模具和树脂粉料加热时间的计算方法。

    youdao

  • The influences of powder particle diameter and processing conditions upon the factors like product property, inner structure and existence of oxide in rotational molding processing were discussed.

    本文讨论了摇摆滚塑成型粉料粒径大小、工艺条件等对产品性能内部结构氧化物存在因素的影响

    youdao

  • The process of rotational foaming molding of liquid reactive resin was studied, with unsaturated polyester resin as the shell of unfoamed resin moulded part, and polyurethane as foamed core layer.

    不饱和聚酯树脂作为发泡树脂成型制品外壳聚氨酯树脂发泡形成泡沫层,研究了液体反应树脂旋转模塑发泡成型泡沫夹层制品的工艺过程

    youdao

  • The base theory would be found though the study of plastic heated by microwave for the succedent rotational micro-wave heating molding.

    微波加热塑料研究,主要日后滚塑工艺微波加热研究提供理论依据

    youdao

  • The base theory would be found though the study of plastic heated by microwave for the succedent rotational micro-wave heating molding.

    微波加热塑料研究,主要日后滚塑工艺微波加热研究提供理论依据

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定