The mixing temperature of the flow is gained from the heat balance equation.
通过建立热平衡方程，求出流体混合温度。
The influence of the mixing temperature, mixer and processing technology on the dispersibility of nano-ZnO in BR compound was investigated.
研究不同的加工温度、混炼设备、加工工艺对纳米氧化锌在BR胶料中分散性的影响。
The effects of mixing temperature, mixing time, crosslinking agent systems and high temperature repeated mixing on the mechanical properties of SBR/PE/PVC blends were studied.
介绍了开炼法制备SBR/PE/PVC多元共混体的共混温度、共混时间、交联体系及共混体高温返炼对材料力学性能的影响。
The influence of the mixing temperature and blending ratio on the mechanical properties of CR/PVC blend was investigated and the microstructure of CR/PVC blend was observed on TEM.
研究了混炼温度和橡塑共混比对CR/PVC共混物力学性能的影响，并通过电镜观察CR/PVC共混物的微观结构。
At the same time, the lower mixing temperature and compacting temperature of WMA has significantly promote the project quality and construction in the cold moisture environment of tunnel.
同时，在隧道阴冷潮湿的特殊环境条件下施工，WMA较低的拌和压实温度对于保证工程质量意义重大。
The result shows, the ester exchange reaction did take place in PC/PET melting blend system, the extent of exchange reaction depends on content of the components, mixing temperature and mixing time.
结果表明，PC/PET共混体系在熔融过程中有酯交换反应发生，反应程度与组分含量、熔融温度和共混时间有关。
That is, if we take the derivative G of delta G of mixing the partial derivative with respect to pressure, at constant temperature, of course, there's no explicit pressure dependence.
就是说，如果我们对,混合物的△,对压强求导，温度不变，当然，不是对压强的显函数。
In general, the Lord salt concentration, temperature increase coating, and under the condition of mixing, can allow the more current density.
一般情况下﹐主盐浓度增大﹐镀层温度升高﹐以及有搅拌的条件下﹐可以允许采用较大的电流密度。
Valves for reducing point of discharge temperature by mixing cold and hot water in branch water lines are available.
这种阀门能够通过调节冷热水的混合比例来降低排放出的热水的温度。
Assuming a given temperature rise, varying ocean depth and therefore differing rates of mixing and consequent expansion will lead to considerable differences in sea level rise.
假设温度上升，不同的海水深度引起的不同的混合和随之而来的膨胀速度，引起显著不同的海平面上升量。
The appearance of the different spectral type for white dwarfs depends mainly on the difference in temperature and internal mixing degree.
白矮星不同光谱型的表现，主要是由于温度的不同和内部混搅程度的不同引起的。
Electroplating working conditions is to point to the operation of the when electroplating changes factors, including: current density, temperature, mixing and power of the wave, etc.
电镀工作条件是指电镀时的操作变化因素，包括：电流密度、温度、搅拌和电源的波形等。
When the temperature control knob to set a temperature, hot and cold water mixing valve through proportional control into the outlet, the outlet temperature is always constant.
当温度调节旋钮设定某一温度后，混水阀通过调节进入出水口的冷热水比例，使出水温度始终保持恒定。
A predominant process for the manufacture of powder coatings involving continuous compounding of pigment, resin, fillers, additives and hardeners, mixing at elevated temperature.
粉末涂料生产的一个非常重要的过程，在一定的温度下可以连续的把颜料、树脂、填料、助剂和固化剂进行混合。
An ideal gas equation is used for quantitative analysis of gas in industrial production, then by adjusting gas temperature and pressure, it is possible to control mixing ratio of materials.
工业上用理想气体方程对气体进行定量分析，通过调节气体的温度压力来控制物料的配比。
The enthalpy of mixing increased with the increase of temperature and solute concentration.
各体系的混合热均随温度和溶质浓度的增加而增大。
The effect of temperature, air flow rate, stirring speed, initial mixing condition on the reaction rate and the speed form have been studied systematically.
探讨了反应温度、空气流量、搅拌速度、碱比、初始混合状态等因素对晶种制备过程中氧化速率及晶种形态的影响。
In addition to temperature control, mixing, it also has the necessary return of organic synthesis and air displacement function, in addition, aluminum can be changed by changing the synthesis process.
除了温度调节、搅拌以外，还具备有机合成必要的回流和空气置换机能，另外，通过变换铝片可以改变合成的进程。
The influence of monomer mass ratio, reaction temperature, reaction time, emulsifying agent content and mixing speed on polycarboxylic acid type waterproofing agent were studied in this article.
本文研究了单体质量比、皂化反应温度、皂化反应时间、乳化剂掺量、搅拌速度等工艺参数对多元羧酸系防水剂性能的影响。
The effects of the desalting temperature, washing water ratio, electric volt, demulsifier concentration and the mixing strength on the efficiency of desalting and dehydration were investigated deeply.
本文深入探讨了脱盐温度、冲洗水浓度、脱盐电压、破乳剂浓度以及混合强度对电脱盐脱水效果的影响。
The mechanism and process of thermal mixing of fluid with different temperature in a straight pipe were studied, which has general significance in nuclear reactor thermohydraulic process.
探讨了在核反应堆热工流体力学中具有普遍意义的不同温度流体达到热混合均匀状态的过程和机理。
Results showed that with the increase of the adhesive temperature, the mixing speed, the adhesive density and the mixing time, the stability of pigment in adhesive could be improved.
结果表明，提高胶液温度和搅拌速度，延长搅拌时间，增加胶液密度，可以提高着色剂在胶液中的稳定性。
To make the interlining, the mixing ratio and heat boning temperature are decided through the orthogonal layout.
在制备絮片前，采用正交实验法来设计方案，确定各纤维的混合比例以及热烘温度。
The experiment shows that fewer melting-back materials, higher temperature and more mixing time will decrease the mixture content, and heighten the intensity as well.
实验证明，含回炉料少、熔炼温度适当增高、加强搅拌，能减少其夹杂物含量，从而提高其强度。
The compaction characters of recycled asphalt mixtures was investigated by gyratory compaction test, and the mixing and compaction temperature was determined.
采用旋转压实仪研究了再生沥青混合料的压实特性，提出了最佳拌和温度和压实温度的确定方法。
On the principle of PID, the control method of fuzzy PID is discussesed in saving electric energy, the effect of dust collecting, wind mixing and spraying for temperature reducing.
在对除尘器风机实行PID变频调速的基础上，为节约电能，提高除尘效果，提出混风降温、喷雾降温的模糊PID控制思想及策略。
Of double cylinder structure, automatic mixing, temperature control and firm performance.
采用双层缸结构形式，电动自动搅拌，控温保稳性能好。
Photobioreactors suitable for macroalga cell cultivation must offer five fundamental factors:illumination, controllable temperature, air transfer, nutrients transfer, and mixing.
适合大型藻类细胞增殖的光生物反应器需要五个基本因素：光照、温度控制、气体传输、营养物质传输、混合。
Photobioreactors suitable for macroalga cell cultivation must offer five fundamental factors:illumination, controllable temperature, air transfer, nutrients transfer, and mixing.
适合大型藻类细胞增殖的光生物反应器需要五个基本因素：光照、温度控制、气体传输、营养物质传输、混合。
应用推荐