They provide a constant depth of cut and fewer blade changes.
它们提供了切不断深入和减少叶片的变化。
Thee three factors of cutting include cutting speed, feed and the depth of cut.
切削用量三要素包括切削速度、进给量和（或叫吃刀量）。
Dry and wet masonry blades provide a consistent depth of cut with less dust than abrasives.
干湿砖石刀片提供少于磨料粉尘削减一致的深度。
Depth of cut, d, is the normal distance between the unmachined surface and the machined surface.
切削深度d是未加工面与已加工面之间的垂直距离。
This particular model predicts the depth of cut achievable with any given set of process parameters.
这个模糊控制模型可以预测在任何给定一组加工参数时，可获得的切割深度。
It can also be seen that the maximum depth of cut is achieved directly as the cutter engages with the workpiece.
还可以看到当刀具进入工件切削时直接达到最大切削深度。
Early machine tools were operated by craftsmen who decided many variables such as speeds, feeds, and depth of cut, etc.
老式机床通常是由工人操作并由他们决定机床速度、进给量、切削深度等。
Impact cutting and cutting compared, not only can increase depth of cut, but can also reduce the large number of cutting force.
冲击切削与静压切削相比，不仅可以增大切削深度，而且可以大量降低切削力。
In this paper, effects of depth of cut and feedrate on mechanical properties of metallic fiber are investigated by spinning bit.
研究了用自旋转车刀加工金属纤维时，切削深度和进给量对纤维力学性能的影响。
During a facing operation, feed is provided by the cross slide, whereas the depth of cut is controlled by the carriage or compound rest.
在端面车削操作中，进给由横向滑板提供，而切削深度则通过大拖板或复式刀架控制。
As we can see in that figure, the depth of cut (and consequently the load) gradually increases on the successively engaged cutting edges.
就像在此图中能看到的那样，切削深度(及作为结果的载荷)随着切削刃持续进入切削而逐渐增加。
The workpiece is clamped in position, and cutter is located against the setting block, which provides setting or cutter position and depth of cut.
工件被夹持到位，铣刀靠着提供安装或铣刀位置及切削深度的安装台定位。
The selection of a suitable feed depends upon many factors, such as the required surface finish, the depth of cut, and the geometry of the tool used.
合适进给的选择取决于许多因素，例如所需表面光洁度、切削深度和所用刀具的几何形状。
This paper deals with the engagement of gears with circular arc profile in normal plane at the presence of errors on center distance and depth of cut.
本文讨论了法向圆弧齿轮在有中心距偏差及切深偏差时的啮合。
The axial feed is provided by the carriage or the compound rest, either manually or automatically, whereas the depth of cut is controlled by the cross slide.
轴向进给通过大拖板或复式刀架手动或自动提供，然而切削深度则由横向滑板控制。
Grasping the top, knurled section of the depth adjustment rod (Q), slide it up so that the TAB (EE) aligns with the desired depth of cut on the pillar scale (FF).
抓住深度调节杆(Q)的顶部，向上抽，使定位片(EE)的顶面对正柱形尺(FF)上希望的切削深度。
A quadratic model of predicting helical milling force was researched. The effects of spindle speed, feed per tooth, and axial and radial depth of cut were analyzed.
通过统计学中的响应曲面法建立了螺旋铣削过程中切削力的二阶模型，并分析了主轴转速、每齿进给量、轴向和径向切削深度等因素对切削力的影响。
Using Taguchi method to optimize the operation about the depth of cut, the spindle speed and the feed rate. Then the optimal cutting parameters can be drawn after analysis.
应用田口法分析主轴转速、背吃刀量和每齿进给量三个可控因素对表面粗糙度的影响，经过分析可以得出最优的参数组合。
This paper presents the information of the effect, measured with a tele-strain-meter, of work material, feed, cutting speed, depth of cut, number of teeth and helix Angle etc.
本文在高速滚齿机上，利用遥测应变仪，测定了工件材料，进给量，切削深度，切削速度，齿轮齿数及螺旋角等对力矩的影响，并得出径节为8时的力矩公式。
Tangential grinding forces are obtained through monitoring spindle power and the ir variations are studied with process parameters such as depth of cut, feedrate and wheel grit size.
通过测量主轴功率获得切向磨削力，讨论了加工参数，如切深、进给率以及砂轮粒度对切向磨削力的影响。
In many cases of stainless steel cutting operations with carbide tools, a tool life strongly depends on flank notch wear of depth of cut rather than average flank wear of main cutting edge.
硬质合金刀具在不锈钢加工中，其刀具耐用度主要是取决于后刀面边界磨损而不是主切削刃后刀面的平均磨损量。
The conditions which have an important influence on metal cutting are work material, cutting tool material, cutting tool geometry, cutting speed, feed rate, depth of cut and cutting fluid used.
对金属切削有重要影响的条件有工件材料、刀具材料、刀具几何形状、切削速度、进给率、切削深度和所用的切削液。
It's possible to misjudge the depth of a cut, making it so deep that it requires stitches (or, in extreme cases, hospitalization).
有可能对切削深度产生误判，以至于割得如此之深，需要缝合(或者在极端情况下需要住院)。
The five nuclear weapon states also exchanged in-depth views on the immediate commencement of negotiations at the Conference on Disarmament in Geneva on a Fissile Material Cut-off Treaty (FMCT).
五核国还围绕如何推动日内瓦裁军谈判会议尽快启动“禁产条约”谈判问题深入交换了意见。
In this article, the author demonstrates the measurement of scratched depth on aero cabin glass with light cut and phase contrast in detail.
应用光切法和相衬法，对飞机座舱玻璃划痕深度的测量问题，进行了详细的论述．。
In this article, the author demonstrates the measurement of scratched depth on aero cabin glass with light cut and phase contrast in detail.
应用光切法和相衬法，对飞机座舱玻璃划痕深度的测量问题，进行了详细的论述．。
应用推荐