In this thesis, stress analysis and calculation for a large oxidized reactor considering are made by using ANSYS FEM code.
本课题用ANSYS软件对某大型氧化反应器流固耦合进行了有限元应力分析计算。
With the model, three dimensions FEM rheology analysis to Xia Liujia is finished, and the stress at different time distortion rule are gained, the long-term work character is forecast.
最后用该模型对下六甲面板堆石坝作了三维有限元蠕变分析，得到坝体在不同时期的应力及变形规律，预测了坝体长期的工作性态。
Kinematic hardening model was used in FEM analysis and the response behaviors of transient local stress strain for material was also considered.
有限元分析采用了随动强化模型，并考虑材料瞬态局部应力应变的响应特性。
Simulating the deformation of the steel plate by induction heating in Finite Element Method(FEM), including temperature analysis, stress analysis and deformation analysis.
对钢板感应加热成型进行有限元分析，包括钢板截面的温度分析，应力分析，变形分析等。
Stability method based on slip surface FE stress and shear strength reduction method are two principal methods for FEM slope stability analysis.
基于滑面上应力分析法和强度折减法是边坡稳定有限元分析方法中两类主要的方法。
In this paper, FEM is used to establish the calculating model of beam axle of compound suspension. After verification by experiment, the model is employed for stress analysis of beam axle.
本文用有限元方法建立复合式悬架车桥的计算模型，经试验验证后，用于车桥横梁的应力分析。
Firstly, the actual stress history of the projecting beam's maximal stress area is acquired by integrating the three-dimensional FEM analysis calculation and the dynamic stress test at field.
本文通过三维有限单元法分析计算与现场动态应力检测相结合，得到各工况下主梁最大应力部位的实际应力—时间历程。
First, using second constrain, the static state and dynamic analysis applied to the frame of a few thickness plates with FEM modal analysis, distortion, stress, vibration and frequency were gained.
首先在第二种约束方式下，利用有限元模态分析方法对几种不同板厚的机架进行了动、静态分析，得到了机架变形、应力及各阶振型与频率。
To verify the reliability of FEM results, the stress distribution of deformation is measured with mesh method, and the analysis results are compared with the experimental results.
用网格法测量了半球形冲头胀形时的应力分布，并将有限元计算结果与实验结果进行了对比，验证了有限元分析结果的可靠性。
Using method of three dimensional FEM analysis, whole stress distribution in the joints is are obtained.
用三维弹塑性有限元分析方法，全面分析了点焊搭接接头的应力分布情况。
In this article three dimension FEM is adopted in the stress analysis of bottom diversion outlet and notch segment of a RCC gravity dam when flowing design flood.
本文采用三维有限元法，对碾压混凝土坝底孔缺口坝段在过流情况下，顶部未到设计龄期的碾压混凝土和大型导流底孔周边的应力分布进行了分析。
In this thesis, the FEM stress analysis and strength design criteria, multi-axes strength theory and computation, limit load analysis method of arch DAMS are concerned.
本文结合工程实际，在拱坝有限元应力分析方法与强度设计准则、多轴应力强度安全计算、拱坝极限荷载分析理论和方法等方面开展研究。
When the upper and the lower half-planes are of the same parameters, the stress field of crack of orthotropic composite materials can be obtained. The derived equation is verified with FEM analysis.
当上下半平面材料参数相同时，可获得受弯曲载荷正交异性复合材料板裂纹尖端应力场，并利用有限元算例分析验证了理论结果的正确性。
This paper presents a report of the stress analysis of a cylindrical shell, with a reinforced hole, by use of the mixed method in FEM.
本文提供了一篇用有限单元混合法对开孔补强的圆柱壳进行应力分析的报告。
There are mainly three methods in the second system stress analysis of the orthotropic steel deck, P-E method, the equivalent girder beam method and the FEM.
薄壁钢扁平箱梁正交异性板钢桥面系第二体系应力的计算方法主要有P -E法、等效格子梁法和有限元法等。
Finally, based on the stress fields of FEM analysis, the most dangerous sliding mode and the minimum anti-sliding factor are searched by parallel recombination simulated annealing algorithm.
最后基于该方法计算的应力场，应用并行组合模拟退火算法搜索坝基最危险滑动模式及相应的最小安全系数。
A stress analysis of a diesel engine crankshaft is made by FEM based on dynamics analysis to determine the position of the initial crack and its propagation direction.
在内燃机动力分析的基础上，运用有限单元法，通过对曲轴应力分析，确定了裂纹启裂部位和扩展方向；
On the basis of FEM stress analysis of a sphere tank, it can be concluded the arrangement of weld in high stress area which was one of the most important exterior factors that cause weld cracks.
通过对球罐的整体应力分析，指出将焊缝布置在高应力区域是造成焊缝裂纹的重要外部因素之一。
The two dimension (2D) finite element analysis (FEM) of the interfacial stress distribution during tension of rubber modified polypropylene (PP) alloy was made by means an ANSYS software.
应用ANSYS软件对橡胶粒子改性聚丙烯（PP）合金拉伸过程中界面应力分布进行了有限元分析。
Aiming at reasonable stress distribution of tower and girder, reasonable alignment of bridge, FEM computation and optimization analysis are combined to determine the reasonable cable tension.
以塔和梁的应力分布合理及梁的线形为目标，采用有限元计算与优化分析相结合的方法来确定斜拉桥的合理成桥索力。
Objective Three dimensional finite element method (FEM) is suitable for the analysis of the stress and deformation of the internal fixation plate and its modified type of the centrally convex shape.
目的三维有限元法(FEM)适于内固定钢板和其改为中心外凸形状进行应力和变形分析。
Computer simulation on complicate shaped parts during quenching process has been realized by using FEM analysis of temperature field phase transformation-stress and strain.
籍助于温度场-相变-应力和应变的有限元分析方法(FEM)，实现了复杂形状工件淬火过程的计算机模拟。
Computer simulation on complicate shaped parts during quenching process has been realized by using FEM analysis of temperature field phase transformation-stress and strain.
籍助于温度场-相变-应力和应变的有限元分析方法(FEM)，实现了复杂形状工件淬火过程的计算机模拟。
应用推荐