A lubricating oil pump shaft and a CAM transmission shaft are respectively sheathed in series in two inner cavities.
两内腔内分别串套机油泵轴和凸轮传动轴。
Chemical composition analysis, mechanical property test and microstructure examination were used to analyze the early fracture of power plant's turbine main oil pump shaft.
采用化学分析、力学性能测试和金相检验等手段,对某电站汽轮机主油泵轴的早期断裂进行了分析。
Conducting oil pump prime the pump, pump cover, bearing, bracket, shaft, seals, bearings, impeller of eight large component parts.
导热油泵首要由泵体、泵盖、轴承体、支架、主轴、密封、轴承、叶轮八个年夜的零部件组成。
Pump drive shaft and bushing wear, the tolerance clearance increases, will affect oil pump.
齿轮泵主动轴与衬套磨损后,其配合间隙增大,必将影响泵油量。
As there were leak on contact place between shaft and rotor body in built up hollow rotor, dropping discharg gas speed of pump and efficiency applied of oil sealed sliding vane rotary vacuum pump.
组合式空心转子由于轴头与转子体之间的结合面存在着渗漏,使泵的抽气效率性能下降,从而影响其在应用中的效率。
The revolving direction, internal oil hole position and spline shaft of the domestic pump are modified to meet the installation requirement.
为了满足安装的要求,对国产齿轮泵的旋向、内油孔位置和花键轴等进行了改造。
In order to improve the efficiency of the quality test and control of the head shaft of oil pump, we designed a general measurement apparatus for measuring the diameter of the head shaft.
为了提高机油泵主动轴的质量检验和质量控制的效率,设计了一个轴径通用检测装置。
The utility model has the advantage that the long service lives of the pump and the oil film of a rotor shaft and an end surface can be maintained under the condition of high-speed rotation.
即使在高速转动状态,也能保持转子轴向端面的油膜,泵的使用寿命长。
The special machine tools for shaft parts' research and design is in the field of "reconstruction of machine technique" . This topic came from the project of XinWei oil nozzle & oil pump Cop.
本论文课题《轴类零件专用机床的研究与设计》来源于江苏南通星维油嘴油泵厂的实际工程项目。
An oil pump (18) is arranged on the external part of the casing of the gear box and on a power output shaft (17), and an oil cylinder (9) is arranged on the rear upper part of the gear box.
在变速箱的壳体外部,于动力输出轴(17)上装有油泵(18),而油缸(9)被安放在变速箱的后上部。
Application: Main shaft of airplane engine or machine tool, high frequency motor, air compressor, oil pump and so on.
应用领域:飞机发动机或车床主轴,高频发动机,空气压缩机,油泵等。
Optimization of Shaft Size and Centralizer Span of Single Screw Pump in Declined Oil Well. Chinese Journal of Computational Mechanics. 1(19):58-62.
隋允康、任旭春。斜井单螺杆抽油泵柱和扶正器间距的最优设计。计算力学学报,2002,1(19):58-62。
Optimization of Shaft Size and Centralizer Span of Single Screw Pump in Declined Oil Well. Chinese Journal of Computational Mechanics. 1(19):58-62.
隋允康、任旭春。斜井单螺杆抽油泵柱和扶正器间距的最优设计。计算力学学报,2002,1(19):58-62。
应用推荐