The system inlet temperature is less than the lower warning threshold.
系统进气孔温度低于下限警告阈值。
The system inlet temperature is less than the lower critical threshold.
系统进气孔温度低于下限临界阈值。
The system inlet temperature is greater than the upper critical threshold.
系统进气孔温度高于上限临界阈值。
The effects of inlet temperature and inlet velocity were taken into account.
实验考虑了进气速度、进气温度对贫油熄火油气比的影响。
Inlet temperature distortion is one of the key factors effecting engine stability.
发动机进口温度畸变是影响发动机稳定性的关键因素之一。
Whereas, the heat transfer of turbulence liquid film flow is not sensitive to liquid film inlet temperature.
湍流时，热量传递对液膜进口温度的反应不如层流敏感。
The article analyses the best inlet temperature of false twister in polyester distortion technique by examples.
通过举例说明在聚酯变形工艺中最佳的假捻器入口温度。
The effects of the cooling water and freezing water inlet temperature are also predicted. The results are reasonable.
对地下水源热泵机组的性能随着冷却水、冷冻水入口水温的变化情况做了预测，结果合理。
T he flow rate regulation range was too narrow, and the change of heat removing capacity depended on the change of inlet temperature.
揭示了液体流率受管道结构等条件的限制，合理调节范围较窄，服装温度比效率不会很高，应主要靠调节进口液温来改变服装的散热量。
The inlet temperature and internal temperature of exhaust catalyst for two stroke moped are tested under different vehicle driving speed.
在不同车速行驶工况下对二行程轻便摩托车用尾气催化剂的入口及中心温度进行了测量与分析。
The higher the normal load, the smaller the effect of the lubricating oil inlet temperature and rolling speed on the traction coefficient.
随着载荷增大，入口油温和滚动速度对拖动系数的影响减小；
The measures to solve these problems in heating transport with PPD and lowering the mini - mum inlet temperature for Daqing Oil are proposed.
提出了加降凝剂进行热处理输送、适当降低规程中的大庆原油最低进站温度等改进措施。
For rolling dryer, the higher filling power value corresponds to downstream quickly drying way, higher inlet temperature and moisture content.
对于转筒式烘丝机，采用顺流烘丝方式，较高的来料温度和水分，较大的热风流速，可获得较高的烘丝填充力。
Increasing overall flow velocity and depressing the inlet temperature of cooling water has little effect on improving temperature distribution.
提高冷却水的总流速和降低进口温度对电池内温度分布的改善作用不好。
The performance of gas turbine has relation with the environmental temperature, and its output is reduced with increase of gas inlet temperature.
燃气轮机的性能与环境温度有关，其出力随空气进气温度升高而降低，燃气轮机的进气冷却是增加其出力的最有效的方法。
Unit energy consumption of the extruder decreases as the speed increases, but raises with the pressure, inlet temperature, plastics segment increased.
挤出机的整机单耗则随着转速的增加而降低，随着压力、进料口温度、塑化段温度增加而上升。
An effective method for maintaining the vacuum in condenser is to change the flow rate of circulating water according to its different inlet temperature.
在不同循环水进口温度条件下，合理改变循环水流量是维持凝汽器真空的有效办法。
Cooling towers' influence on the inlet temperature of circulating water was also considered to determine optimum running mode of circulating water pumps.
同时考虑闭式循环水系统中冷却塔对循环水入口温度的影响，确定出循环水泵最优运行方式。
This paper discusses the effect of compressor inlet temperature on its performance, thereby puts forward some measures to keep the inlet temperature constant.
本文分析了压气机性能试验中压气机进口温度变化对性能的影响，提出了保持进口恒温的一些措施。
With the increase of the turbine inlet temperature of high performance aero-engine day by day, the turbine coating blade coating technology has been widely used.
随着高性能航空发动机涡轮进口温度日益提高，涂层技术在涡轮叶片上得以广泛应用。
In this article, the main influencing factors on condensation heat transfer include air flow rate, coolant flow rate, coolant inlet temperature and mixed gas velocity.
在本课题中，影响传热过程的因素主要有空气含量、冷却水流量、冷却水温度及混合气气速。
The influences of the Angle of tilt and the inlet temperature and concentration and the absorption pressure on the performance of heat and mass transfer are discussed.
讨论了斜板尺寸和进口温度、浓度及吸收压力等参数对传热传质性能的影响。
Higher gas inlet temperature, lower steam pressure or pinch point temperature difference lead to lower exhaust gas temperature, larger evaporation and higher efficiency;
提高进口烟气温度、降低蒸汽压力或减小节点温差，均可显著降低设计出口烟气温度，从而增大蒸发量，提高热效率；
The experimental results show that in the process of flow excursion the mass flow rate and the inlet temperature decreases, while the exit temperature increases smoothly.
研究结果表明：在发生静态流量漂移时，系统循环流量下降、加热段的进口温度下降而出口温度上升；
Table 1 contains the recommended temperature that the heatsink base test point or the air inlet temperature should remain below during the thermal evaluation of a system.
表1含有进行系统热量测量时散热器基座测试点或空气入口温度应该低于的推荐温度值。
Properly increasing the furnace inlet temperature, strengthening the process management and selection of aluminum diffused plates could effectively protect the corrosion.
适当提高尾气入口温度、加强工艺管理和采用渗铝板进行包补是防止腐蚀的有效措施。
Based on the heat exchange theory between air and rock, the feasibility of decreasing air inlet temperature by temperature regulating action of shallow ground is discussed.
根据空气与岩体的热交换原理，探讨了利用浅部地层调温作用来降低深井入风温度的可行性。
It can be seen that if the engine air inlet temperature is higher and the ambient pressure is lower than the standard conditions, the power output of the effects will be lower.
可以看出，如果在发动机的进气温度较高，环境压力低于标准的条件下，输出功率的影响将降低。
It can be seen that if the engine air inlet temperature is higher and the ambient pressure is lower than the standard conditions, the power output of the effects will be lower.
可以看出，如果在发动机的进气温度较高，环境压力低于标准的条件下，输出功率的影响将降低。
应用推荐