The flaking do increases and undulates the fatigue crack growth rate.
钢中的白点能增加疲劳扩展速率并使扩展速率发生波动。
The fatigue crack closure and fatigue crack growth rate in the high strain region of SCT specimen are studied.
本文研究了SCT试样高应变区的疲劳裂纹闭合效应和疲劳裂纹扩展速率。
The fatigue crack growth rate is the core for predicting fatigue life by use of fatigue crack propagation (FCP) theory.
疲劳裂纹扩展率表达式是采用疲劳裂纹扩展理论预报疲劳寿命的核心。
On the basis of this, an automatic measurement technique of fatigue crack length in fatigue crack growth rate test under corrosive circumstance is established.
在此基础上，建立了腐蚀环境下疲劳裂纹扩展速率试验中裂纹长度的自动检测技术。
Study of fatigue crack growth rate and fatigue life calculation under random loading is very important for the reliable life prediction of engineering structures.
变化载荷作用下裂纹扩展律和疲劳寿命的计算对工程结构的寿命的可靠预测是十分重要的。
The fatigue crack growth rate and CTOD tests on type 304 stainless steel and weld metal were studied over the temperature range -162 degree C to room temperature.
疲劳裂纹扩展速率和CTOD测试型不锈钢304研究和焊缝金属的温度范围-162度到另一个房间 温度。
A small sample method for testing fatigue crack growth rate curve of steel was presented in this paper using a formula of two-dimensional one-side tolerance factor.
应用二维单侧容限系数公式，提出了一种测定金属材料疲劳裂纹扩展速率的小样本方法。
The studies were carried out of the test of fatigue crack growth rate and relative to the microscopic morphology of fracture surface in certain high-strength steels.
本文用宏观和微观方法测量了几种高强度钢的疲劳裂纹扩展速率，用金相和断口复型法观察了疲劳断口的微观形态以及与显微组织的关系。
For CH joint, when the initial crack is located in hard zone, the closer the initial crack is to the hard soft interface, the slower the fatigue crack growth rate is.
起始裂纹在硬区的软对硬力学性能非对称焊接接头，起始裂纹越靠近软区，疲劳裂纹扩展速率越慢；
Based on the features of the three-dimensional crack, an experimental method was presented to measure the near-threshold fatigue crack growth rate and threshold of the corner crack at a hole.
基于三维裂纹特征，本文提出了一种测量孔边角裂纹近门槛区疲劳裂纹扩展速率及门槛值的实验方法。
It is shown that a regular pattern distribution of scattered alloying zones which surrounded by phase transformation zone can retard the fatigue crack growth rate and improve the fatigue life.
研究表明，大量规则分布、互不重叠的合金化区及其周围的相变硬化区从总体上降低了疲劳裂纹扩展速率，提高了材料的疲劳寿命。
The technique of measurement of growth, rate of fatigue short crack with indirect KC (IDC) potential system and AC potential system was investigated.
木文研究了间接直流电位法（IDC法）和交流电位法（AC法）用于监测疲劳短裂纹扩展速率的有关技术问题。
If the failure is defined as the final fracture of a component, then both S-N curves and crack growth rate curves reflect the fundamental material behavior under fatigue loading.
如果都把一个构件的最终断裂作为疲劳破坏的定义，则S - N曲线和裂纹扩展率曲线均是反映金属在疲劳载荷作用下的基本材料特性。
Fatigue damage estimation of the tendons was made using fracture mechanics approach, establishing the fracture crack growth rate model and limit state equations for failure modes.
疲劳寿命的计算采用断裂力学方法，建立疲劳裂纹扩展模型和失效模式的极限状态方程。
Fracture mechanics is adopted to estimate the fatigue life of structural members, and among the rest, crack growth rate formula is studied.
本文采用断裂力学方法来估算结构构件的疲劳寿命，这其中主要围绕裂纹扩展速率表达式展开研究。
The results show that the crack growth rate under high-low cycle complex fatigue load is greater than that under low cycle fatigue load, and so the fatigue life is obviously reduced.
结果表明：与纯低周载荷作用相比，高低周复合载荷下球墨铸铁的裂纹扩展速率明显加快，极大地降低材料的疲劳寿命。
Result show that the trace boron additive causes the changes in the mode of fatigue crack propagation and its route, so that crack growth rate of 40MnB is lowered.
结果表明，微量合金元素硼改变了裂纹扩展途径和扩展方式，从而降低了疲劳裂纹扩展速率。
The fatigue life for bracket was predicted by way of the unique crack growth rate model incorporating the above SIF functions and the predicted results were in good agreement with the experiment data.
结合裂纹扩展率单一曲线模型对肘板裂纹扩展寿命进行了预报，预报结果与实验结果符合得较好，说明所采用的方法可行。
The fatigue life for bracket was predicted by way of the unique crack growth rate model incorporating the above SIF functions and the predicted results were in good agreement with the experiment data.
结合裂纹扩展率单一曲线模型对肘板裂纹扩展寿命进行了预报，预报结果与实验结果符合得较好，说明所采用的方法可行。
应用推荐