Smelting of SiMgREBa alloy with rare earth rich slag, barite and lime in electric-arc furnace is introduced in the paper.
叙述了在电弧炉中用稀土富渣、硅铁、重晶石、石灰等原料冶炼稀土硅钡镁合金的研制过程。
Summarizes the first industrial experiment on protecting from water erosion by spraying blade, concludes that electric-arc spraying should be perfected and popularized in this respect.
通过对叶片防水蚀喷涂保护的首次工业性试验进行了总结，并认为喷涂在这方面应该得到完善和推广。
Edison was not the first person to have thought of using electricity for illumination: cumbersome electric arc-lighting had been employed in public Spaces and factories for a number of years.
爱迪生不是第一个想到用电照明的人；许多年来，笨重的电弧灯就在公共区域和工厂投入使用。
To take away the refining part of the steel making cycle off an electric arc furnace, which is discussed elsewhere, is an excellent start.
把炼钢周期中的精炼阶段从电弧炉中移走（这个问题将在别处加以讨论），是一个良好的开端。
Connect the ground connection of the electric arc welding equipment as near as possible to the welding point on the part to be welded.
将电弧焊设备上的接地连接尽可能近地连接到将要焊接零件的焊接点上。
This welding process joints work pieces by melting the electrode and the base metal with the heat from the electric arc between the electrode and the work piece.
它是一种利用焊条与工件之间电弧产生的热量熔化焊条和母材而将被焊工件连接起来的焊接方法。
Principles of pyrogenic process, wet process and other methods are more fully described. The feasibility of the technology of comprehensively treating electric arc furnace dust is discussed.
详细陈述了火法、湿法以及其它方法处理电弧炉炉尘的原理，并且简述了这些工艺的可行性。
When an electric arc is produced in the material, light is produced.
一种物质中产生电弧时，光就产生了。
The supersonic velocity electric arc spraying technology (HVAS) has gained satisfactory solution.
电弧超音速喷涂技术(HVAS)可以有效的解决此问题。
The microhardness of JCW-S-AM coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.
采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW - S - AM涂层，利用显微硬度计测定各种涂层的显微硬度。
The cathode electric arc source is used as the source of ion infiltrating metals.
本文用阴极电弧源做离子渗金属源。
Electric arc discharge of the tips installed in BSP source produces intense ultraviolet ray emission with a spectrum continuously extended to the range of visible light.
针式火花预电离源利用热电弧发出强烈的紫外光，其发射光谱范围从可见光连续延伸到紫外。
The non-linear operation reactance model of the 32 MV·A high impedance electric arc furnace was established.
根据测量结果建立了石钢32MV.A高阻抗电弧炉工作电抗模型。
The electric arc furnace steel-making productivity has gained rapid progress in the recent years.
近几年来，电弧炉炼钢生产率有较大的提高。
Using the high voltage between the two electrodes to breakdown of gas layer, thus generating an electric arc ignition devices.
利用高电压来击穿其两电极之间的气体绝缘层，从而产生电弧的一种电火花点火设备。
In the electric arc spray coating the oxide content was about 10%.
而且电弧喷涂涂层中具有约10%左右的氧化物含量。
The melting and reduction of scheelite acted by high temperature electric arc are very fast.
在高温电弧作用下，白钨矿粉的熔化还原速率很快。
Stable electric arc can be ensured from undercurrent to high current.
从小电流到大电流都可以保持稳定电弧。
Characteristic of direct reduced iron and its present status in service in electric arc steelmaking Changcheng Company had been summarized, its effect has been analyzed further.
概述了直接还原铁的特性及在我厂电弧炉炼钢中的使用情况，并将其效果作了进一步分析。
A new technology-the electric arc spraying technology combined by powder is introduced.
介绍一种新型电弧喷涂技术粉末复合电弧喷涂技术。
This article makes a brief description of production by some electric arc furnaces at home and abroad, sums up various EAF technologies presently existing.
本文简要介绍了世界和国内的一些电弧炉生产情况，总结了目前已有的各项电弧炉技术。
This paper introduces the technological process, equipment characteristics and the benefit of vaporized cooling project of Consteel electric arc furnace.
介绍了康斯迪电弧炉汽化冷却项目的工艺流程、设备特点、经济效益。
New controlling technology make better performance of starting arc, it can choose the most comfortable electric arc by adjusting the electric arc force knob.
新的控制技术使引弧性能更好，可通过电弧力旋钮调节电弧的柔和性，选择您最舒服的电弧。
The electric arc furnace (EAF) steelmaking is the main method used to produce special steel and alloy steel.
电弧炉炼钢是用来生产特殊钢和高合金钢的主要方法。
Welding process factors consist of welding electric current, electric arc voltage, welding speed, etc.
焊接工艺因素包括焊接电流、电弧电压、焊接速度等。
And also, the electric arc erosion of contact materials is engendered by heat effect of arc and other discharge phenomenon during the open and close of electric contact materials.
还发现触头材料的电弧烧损主要是触点在断开和闭合的过程中，产生电弧或其它放电现象的热效应所造成的。
And also, the electric arc erosion of contact materials is engendered by heat effect of arc and other discharge phenomenon during the open and close of electric contact materials.
还发现触头材料的电弧烧损主要是触点在断开和闭合的过程中，产生电弧或其它放电现象的热效应所造成的。
应用推荐