没有可用的引导设备。
Select Set Boot Sequence: Configure as 1st Boot Device.
选择设置引导顺序：配置为第一引导设备。
When a boot device is found, the Linux kernel boot process begins.
找到引导设备后，开始Linux内核引导过程。
The current BIOS setting do not fully support the boot device.
当前的BIOS设置并不完全支持这个启动设备。
Set up HBA to enable the BIOS and select the boot device from DS8000.
将HBA设置为支持BIOS，并选择从DS8000启动设备。
At this stage, you need to set up the boot device in the Qlogic BIOS.
在该阶段，您需要在QlogicBIOS中设置根设备。
Device, Second Boot Device, Third Boot Device, Boot Other Device.
即第一启动设备、第二启动设备、第三启动设备、其他启动设备。
Now, you need to select the boot device on which to install Linux.
现在，需要选择根设备安装Linux。
Another important QEMU launch option is -boot, which specifies the boot device.
另一个重要的QEMU启动选项是- boot，它指定了启动设备。
Enters the boot mode selection screen, allowing you to choose a boot device.
进入引导模式选择画面，让您选择一个启动设备。
The BIOS loads the first sector of the boot device and executes the code it contains.
BIOS加载启动设备的第一个扇区并运行其包含的代码。
(If you will need this option later, define the third boot device as Network BOOTP).
(如果您以后还需要这个选项，那么将第三引导设备定义为Network BOOTP)。
When a boot device is found, the first-stage boot loader is loaded into RAM and executed.
当找到一个引导设备之后，第一阶段的引导加载程序就被装入RAM并执行。
The boot sector is always at the same place-track 0, cylinder 0, head 0 of the boot device.
引导扇区总是在同一个位置—引导设备的磁道0、柱面0、磁头0。
This first sector will continue the boot process by loading the rest of the kernel from the boot device.
第一个扇区从引导设备上加载内核的其余部分继续引导过程。
You must also record the path to the alternate boot device, so the system can boot if the submirror fails.
您还必须记录到备选根设备的路径，这样如果子镜像失败了，系统仍然可以启动。
Configure and ensure the boot list is pointing to the standby BOS as the first boot device, as shown in Listing 17.
配置并保证启动列表将备用BOS作为第一启动设备，如清单17所示。
The method for setting up boot devices and selecting a boot device at startup is specific to your system and its BIOS.
设置引导设备和选择在启动时引导设备的方法特定于您的系统及其BIOS。
A boot device can be a floppy disk, a CD-ROM, a partition on a hard disk, a device on the network, or even a USB flash memory stick.
引导设备可以是软盘、CD - ROM、硬盘上的某个分区、网络上的某个设备，甚至是usb闪存。
Your boot device is the cartridge disk controller (DP), which you associate with the external file from the software kit (iu6_dp0.dsk).
引导设备是盒式磁盘控制器 (DP)，您可以将其与来自软件工具包的外部文件 (iu6_dp0.dsk) 关联。
If SDDPCM is desired to be used for the boot device, another restart of the system is required after installation of the SDDPCM software.
如果想要使用SDDPCM作为引导设备，那么必须在安装了SDDPCM软件之后对系统进行一次重启。
And you get an error I9990301 disk failure or disk reset failed then you have to switch boot sequence and make hd1 the first boot device.
可能会产生一个错误I9990301diskfailureordiskresetfailed，这时必须切换引导次序，让hd 1成为第一个引导设备。
Verify in the LSI configuration utility that the daughter card is enabled and included in the boot list, preferably as the first boot device.
通过LSI配置实用程序检查子卡是否已经启用并包含在引导列表中，子卡最好是第一个引导设备。
You can optimize the process of determining the boot device by selecting the device from which you'll most commonly boot (typically, the hard disk).
通过选择最经常引导的设备（通常是硬盘）可以优化确定引导设备的过程。
To boot using the IBM Installation Toolkit Live DVD, make sure your system has the CD/DVD-ROM drive or the Network Adaptor as its first boot device as follows
要使用IBMInstallationToolkitLiveDVD引导机器，请确保您的系统使用 CD/DVD-ROM驱动器或网络适配器作为其第一引导设备，方法如下
Operator Notes: The boot device should be preceded by checking whether the coupling nut loose or fall off, if in time to tighten the nut with the wrench.
操作工须知：在启动设备前应先检查联轴器的螺母是否有松动或脱落，如有要及时将螺母用扳手把紧。
Even equipped with the "engine to prevent the boot device", but if the case of sweeping the streets with the trailer Qieju Group, was arrested still have to bow.
即使装备了“引擎防止启动装置”，但若遇上采用拖车扫街的窃车集团，照样得俯首就擒。
The server will need to be rebooted after the update process, so make sure the bootlist is showing the target alternate disk as the first boot device (as seen in Listing 7).
服务器需要在更新过程完成后重新启动，所以要保证启动列表显示目标备用磁盘作为启动设备（如清单 7 所示）。
Creates the system boot image on a specific device.
在特定的设备上创建系统引导映像。
Then, the kernel starts to boot and device drivers begin to register devices with the rest of the system.
然后内核开始启动，设备驱动程序开始向系统的剩余部分注册设备。
应用推荐